抗倍特板材作為高密度的人造板材，質地很堅硬。因此富美家抗倍特板廠家認為，使用抗倍特工作時應注意砂磨與拼接操作。

As a high density artificial board, the quality of the anti Beite board is very hard. Therefore, the manufacturer of Fumeijia MP laminate believes that sanding and splicing should be paid attention to when using MP laminate.

砂磨時，按順序分別采用80＃、220＃和320＃砂紙對邊緣進行砂磨。打磨速度以2.5米/15-20分鐘為基準。打磨時，應注意不要損壞表面裝飾層。打磨結束后，用拋光劑對邊緣進行拋光處理。可使用人造大理石的拋光蠟作為拋光劑，拋光程序如下:

During sanding, the edges shall be sanded with 80 ＃, 220 ＃ and 320 ＃ sandpaper in sequence. The grinding speed is based on 2.5m/15-20min. When grinding, be careful not to damage the surface decorative layer. After polishing, polish the edges with polishing agent. The polishing wax of artificial marble can be used as polishing agent, and the polishing procedure is as follows:

a.用柔軟的棉布沾取適量拋光蠟，對邊緣進行擦拭；

a. Use a soft cotton cloth to dip an appropriate amount of polishing wax and wipe the edges;

b.待拋光蠟干燥后，再對邊緣涂一層拋光蠟，并用布進行擦拭，使之出現光澤，再涂一層拋光蠟，并用干凈的布擦拭，直至邊緣光亮。

b. After the polishing wax is dry, apply a layer of polishing wax on the edge and wipe it with a cloth to make it shiny. Apply another layer of polishing wax and wipe it with a clean cloth until the edge is bright.

拼接板件時，應注意以下幾點:

Pay attention to the following points when splicing plates:

a.粘合劑的涂布量需要控制在2.5-3.0g/cm2，并且要確保涂布到全部粘接表面；

a. The application amount of adhesive shall be controlled within 2.5-3.0g/cm2, and it shall be ensured that the adhesive is applied to all bonding surfaces;

b.拼接后，用夾子壓合30分鐘左右。豎直方向粘合時，一定要開口，增大粘合面，以確保粘合的強度；

b. After splicing, press with clips for about 30 minutes. When bonding in the vertical direction, be sure to open and increase the bonding surface to ensure the bonding strength;

c.一旦發現被粘合部件有爆口等缺陷，需要將光滑平整的一面朝外，以保證粘合的質量。

c. Once it is found that the bonded parts have defects such as bursting, the smooth and flat side needs to be outward to ensure the quality of bonding.

抗倍特板在安裝結束時，如果表面出現斑點或污跡，可用毛巾沾取少量油性清潔劑(油與丙酮的混合物)輕輕擦拭去這些斑點或污點。如果沒有斑點或污跡，用一般清潔劑如肥皂加水，或洗潔精加水擦拭即可。更多相關使用就來我們網站http://www.xamgdj.com咨詢了解吧！

At the end of the installation of the anti magnification special plate, if there are spots or stains on the surface, use a small amount of oily cleaner (mixture of oil and acetone) dipped in a towel to gently wipe away these spots or stains. If there is no spot or stain, wipe it with general detergent such as soap and water, or detergent and water. Come to our website for more relevant use http://www.xamgdj.com Ask and understand!