1、 Vertical plane

步用專用切割工具將防火板材裁剪成所要求的規格，特別注意防火板材每一條邊需多留6毫米當作壓邊的用處。飾面防火板附著到基層板上面時，個貼表面積較小的垂直面。

The first step is to cut the fireproof board into the required specifications with a special cutting tool, and pay special attention to the extra 6mm on each edge of the fireproof board as the purpose of edge pressing. When the facing fireproof board is attached to the base plate, the first vertical surface with small surface area shall be pasted.

施工過程時，基層板的邊和封邊條的后面都一定要上膠，上膠可以使用涂裝和刮涂的具體方法。等約幾分鐘到十幾分鐘萬能膠揮發掉干后，即萬能膠不沾手時，將飾面防火板封邊條謹慎貼到基層板的垂直線旁邊去，隨后再用滾軸或壓力機加壓力以保證飾面防火板黏貼到基層板上面，再將不必要的一部分修剪掉。這是水平面直接貼的方法。

During the construction process, the edge of the base plate and the back of the edge sealing strip must be glued. The specific methods of coating and scraping can be used for gluing. After the all-purpose adhesive evaporates and dries in a few minutes to more than ten minutes, that is, when the all-purpose adhesive does not touch your hands, carefully stick the edge sealing strip of the facing fireproof board next to the vertical line of the base plate, and then apply pressure with a roller or press to ensure that the facing fireproof board adheres to the base plate, and then trim the unnecessary part. This is the method of pasting directly on the horizontal plane.

二、水平面

2、 Horizontal plane

同樣的，將強力膠站到防火板材背部和基材板水平面，直到強力膠不黏手時，將防火板材放進基材板上。要是黏貼的范圍特別大，是能用木塊先間隔時間著放到基材板上邊，再將防火板材放進基材板上，等對正直再將木塊抽出來，將防火板材慢慢地地?cái)D壓到基材板上。

Similarly, stand the strong glue on the back of the fireproof board and the horizontal plane of the base plate until the strong glue does not stick to your hand, and put the fireproof board on the base plate. If the scope of adhesion is particularly large, wood blocks can be placed on the base plate at intervals, and then the fire-proof plate can be placed on the base plate, and then the wood blocks can be pulled out after alignment, and the fire-proof plate can be slowly squeezed onto the base plate.

當飾面防火板被壓貼到基材板時應注意將防火板之間的空氣去除，然后應該再用滾輪用力壓勻一次或送進冷壓機里，或經過旋轉滾筒來加壓，務必使膠能均勻分布，同時避免殘余的空氣在里面。

When the facing fireproof board is pressed to the base plate, pay attention to remove the air between the fireproof boards, and then use the roller to press it evenly once, or send it into the cold press, or pressurize it through the rotating roller. Make sure that the glue can be evenly distributed and avoid residual air in it.

加壓工作做好之后，就可以用修邊機等工具將多余的邊切去，然后再用較鋒利的銼刀將接縫處銼得圓滑些。

After the pressure work is done, you can cut off the excess edge with tools such as trimming machine, and then file the joint more smoothly with a sharp file.

富美家抗菌板http://www.xamgdj.com主要是為您提供相關的行業知識，想要理解更多的知識及內容，請大家持續關注本站。

Fumeijia antibacterial board http://www.xamgdj.com It is mainly to provide you with relevant industry knowledge. If you want to understand more knowledge and content, please continue to pay attention to this website.